FlowCV Logo
Education
M.S. in Power Engineering, Technical University of Munich

Focus: Power Electronics, Electric Drives and Energy Informatics

  • •GPA: 2.41/5.0 - Bayerischen Formel
    • Oct 2023 – PresentMunich, Germany
    B.S. in Electrics and Electronics Engineering, Middle East Technical University

    Focus: Energy Conversion, Power Electronics and Control Theory

  • •GPA: 3.47 / 4.00 (Honor Student)
    • Oct 2018 – Jun 2023Ankara, Turkey
  • •GPA: 1.7/5.0 - Bayerischen Formel
    • Work Experience
    Molabo GmbH, Power Electronics Working Student
  • •Designed and tested motor driver circuits in KiCAD for several water pumps located in the 48V electric engine for commercial boat drives using TI DRV81xx series automotive half-bridge driver ICs
  • •Assembled and reworked the driver PCBs using soldering equipment such as a reflow oven and a hot air soldering station
    • Oct 2023 – PresentMunich, Germany
    TÜBİTAK Space Technologies Research Institute, Part-Time Researcher
  • •Simulated a sequential switching shunt regulator (S3R) in LTSpice that regulates a satellite's busbar voltage by utilizing it's solar arrays using a feedback amplifier
  • •Designed an inrush current limiter circuit by making use of the Miller Capacitance of a MOSFET for the S3R
    • Oct 2022 – Jul 2023Ankara, Turkey
  • •Performed functionality tests on the printed circuit using electronic lab equipment including a Lecroy oscilloscope, power supply and digital multimeter
    • Swobbee GmbH, Embedded Systems Intern
  • •Designed a PCB interface for the test setup of the control unit of battery charging modules that allowed communication between the control unit and a RaspberryPi
  • •Detected faulty battery cells in small electric vehicle batteries by analyzing the charging/discharging curves of several types of batteries
    • Jul 2022 – Sep 2022Berlin, Germany
  • •Mechanically assembled and electrically tested small electric battery charging modules, making them ready to be installed in battery charging stations
    • Rüzgem (METU Center for Wind Energy Research), Intern Researcher
  • •Built a GUI in LabVIEW for an Open-Jet Wind Tunnel, allowing users to control the wind tunnel driver to operate at desired velocity and gather data from sensors
  • •Implemented a Kalman Filter to the differential pressure sensors of the wind tunnel and obtained reliable data readings
    • Aug 2021 – Oct 2021Ankara, Turkey
  • •Simulated and implemented a Linear Quadratic Regulator (LQR) into the controller of the wind tunnel which was initially controlled by a PID controller
    • Projects
    48W Isolated Power Converter, Static Power Conversion II Course Project
  • •Produced a step up flyback converter with opto-isolated feedback that converts 12V-18V to 48V using a current mode PWM controller
  • •Achieved > 80% efficiency with 60kHz switching frequency by manufacturing a suitable transformer
    • Jun 2023
    220V DC Motor Driver, Static Power Conversion I Course Project
  • •Collaborated with a team to implement a current-controlled converter circuit that can rectify grid voltage and drive a 220V(1500RPM) DC Motor using a full bridge rectifier and a specialized buck converter topology
  • •Designed a PCB in Altium to optimize circuit size, and a 3D printed casing in Shapr3D for the circuit, facilitating marketability and prioritizing electromagnetic compatibility
    • Jan 2023
    Water Level Control of Coupled Tanks, Process Control Course Project
  • •Completed a water level control system where an electrical pump provided an in-flow to a leaky upper tank while the water flows to the lower tank.
  • •The water level of the lower tank is controlled by a PI controller run by a digital microcontroller using filtered ultrasonic sensor measurements.
    • Jan 2023
    Software
    ECAD — KiCAD / Altium|Simulation — PLECS/ Simulink / LTSpice|Programming — MATLAB / LabVIEW|Version Control — Gitea / Github|LaTeX|Project Management — Redmine / Odoo|CAD — Shapr3D/Siemens NX
    Languages
    English

    Full Professional Proficiency

    TOEFL iBT 115/120

    (Obtained Nov 2022)

    German

    Professional Working Proficiency

    Deutsch für Ingenieur:innen B2/C1 Program at TUM

    (Sep 2024 - Present)

    Turkish

    Native